Light tobacco smoke controlOne of the world's most efficient HEPA air cleaners in its class. Incorporates H12/13 class certified HEPA filter, normally used in multi-million dollar cleanrooms. This certification under the world's most stringent HEPA filter test, European Norm EN 1822, is the basis for this air cleaners' ability to capture up to 100 times more particles than conventional HEPA cleaners. In fact, while other air cleaners are rated only for particles down to 0.3 microns, IQAir systems have been found to remove particles down to 0.01 microns with close to 99% efficiency.
HEPA Filter
replace every 2-4 yrs
--------------------------------------------------------------------------------
V5-Cell Gas/Odor Filter
replace every 1-2 years
--------------------------------------------------------------------------------
Pre-Filter
replace every 6-18 months
The IQAir HealthPro Plus comes complete with filters, user manual, handsigned Certificate of Performance, set of 4 casters, 10 foot power cord, user guide video (both VHS and DVD) and remote control with batteries.
A picture is worth a thousand words...here's how this high
quality Swiss-made air cleaner is designed:
1. User Control Panel
(comes with remote control unit)
2. Carrying Handle
3. No-Draft Diffuser
4. Cleanroom-Grade HyperHEPA Filter
5. Advanced Gas and
Odor Control Filter (HealthPro Plus only)
6. Snap-Open Locking Arms
7. Six-speed High-Performance Centrifugal Fan
8. Advanced Six-speed Fan Control
9. Pre-Max Pre-Filter (Class F9)
10. Dual Floor Air Intake
There are several extra options available, including ducting
for clean room or hazardous locations, positive or negative pressurization
to control contamination. Pictured below is the duct accessory that can
isolate a sickroom. There's also a duct accessory that can supply clean air
to a bedroom or other type of room needing perfectly clean air. Scroll down
for complete details.
Technical information:
Number of Selectable Fan Speeds 6
Air Delivery (with new filters installed) per Speed
1 - 30 cfm
2 - 60 cfm
3 - 90 cfm
4 - 120 cfm
5 - 150 cfm
6 - 280 cfm
Maximum Coverage Area: 1100 sq ft (based on maximum fan speed and an 8.5
ft ceiling)
System Efficiency for Particles 99.97% or more at 0.3 microns
99.5 for smaller particles
Power Requirements 115 VAC 50-60 Hz The entire electrical system is UL
certified.
Energy Consumption (Max) 1 - 85 W
2 - 120 W
3 - 150 W
4 - 170 W
5 - 205 W
6 - 215 W
Dimensions H 28" W 15" D 16"
Net Weight (including filters) HealthPro 29 lbs
Warranty Period 5 yr on unit including fan motor, excluding filters
Filters
Filter Configuration 1 Pre-Filter
1 Cleanroom grade HyperHEPA filter
Pre-Filter ASHRAE 85% high accumulation media, 55% efficiency at .3 microns,
25 sq ft area
HyperHEPA Filter 99.97% DOP (.3 microns) media, mini-pleat with solvent-free
separators, 40 sq ft area, patented expanded polystyrene (EPS), CFC-free
construction
Average Filter Life Pre-Filter: 6-18 months HyperHEPA Filter: 2-4 yrs
Housing
Housing Material ABS(UV-stabilized), non-offgasing, high-impact resistant
Color of Main Housing/Arms Light Gray/White
Air Intake Two side openings at base of unit
Air Outlet Via diffuser with horizontal 320 degree, 77 sq inch opening on
top of unit
Fan
Fan Motor 700 cfm, 2950 rpm centrifugal, backward curved, maintenance-free
steal ball bearings, UL/CSA registered
Electronic Control Panel
Control Panel Finish Polyester overlay panel
Main Display Liquid crystal display, 16 character x 2 line
Status and Indicator LEDs Timer Status LED, Filter Life Status LEDs, Fan
Speed Indicator LEDs
Display Languages English, French, German, Italian, Spanish
Negative and positive pressure for
isolation and clean rooms.
The IQ air can be ordered with accessory kits
for positive or negative pressurization of isolation and clean rooms. Call
us for complete details and pricing.
InFlow W125
|
The InFlow W125 ducting kit enables any IQAir
filtration system to draw air through a wall or window vent into an
indoor environment. Use of the InFlow W125 is advisable when the
main pollution source is located in adjacent indoor environments or
outdoors.
Enjoy controlled clean air ventilation
An IQAir® filter system combined with an InFlow W125 can be
installed to draw outdoor air into an indoor environment. In this
setup, an IQAir serves as a ventilation system, bringing in
oxygen-rich outdoor air and a filtration system, which removes
undesirable outdoor pollutants such as pollen, mold spores, dust and
exhaust soot. As a result, fresh and filtered outside air comes into
the room. |
|
Create clean positive pressure areas
An IQAir® filter system combined with an InFlow W125, which draws air into a
room will in most cases allow the creation of a positive pressure. This
positive pressure helps to clean the air in a room by constantly flushing
out air pollutants and by preventing outside pollutants from entering the
room.
Application Examples
-
- Protection of allergy
sufferers from pollen exposure in their home
- Protection of patients
from microbiological exposure (e.g. aspergillus) in a hospital
- Creation of clean
research or manufacturing areas (controlled environments)
- Protection of plant
control rooms from corrosive contaminants
- Creation of a clean zone
within a home or office which helps to prevent outdoor pollution from
nature, factories, traffic, agriculture to enter.
Using an InFlow W125 with an IQAir system can
improve indoor air quality by:
-
- diluting polluted air with
clean air
- flushing out air pollutants
- reducing influx of new
outside pollutants due to a build-up of positive pressure
- by increasing oxygen content
in indoor air (when outdoor air is being drawn in)
Installation
The InFlow W125 kit can be easily added to any IQAir filtration unit in a matter
of minutes. As regards the building, the only modification required is a 5" hole
in a window, wall or door which allows you to connect the InFlow W125 aluminum
duct.
The duct may be freely flexed to allow control over the desired vent location.
It is expandable in length, from 10" in its original compressed state, to 39"
when fully extended.
IQAir Compatibility
Compatible with all IQAir filtration devices.
Not compatible with the accessories PF40, VMF, VM FlexVac, VM InFlow and FlexVac.
OutFlow W125
Here is the outflow configuration.
OutFlow W125
Technical Specs Sheet (pdf)
Application
The OutFlow W125 kit allows filtered air from any IQAir® filtration
device to be directed through a wall or window vent. The OutFlow W125
kit can be used to:
-
- create clean areas
- deliver filtered air into cleanrooms or to the
outside
- create negative pressure areas
- create positive pressure areas
Clean Area and Cleanroom Use
The supply of filtered air into an environment helps reduce air
pollution in that environment by dilution and the creation of positive
pressure, which reduces the infiltration of polluted air from outside
the environment. With the OutFlow W125 kit, the filtration device is
positioned outside the clean area or cleanroom, saving valuable space
and reducing noise exposure. It also eliminates the danger of housing
leakage, making it suitable even for certified cleanrooms. |
|
Emission Control
Legislation limits the emission of polluted air to the outdoors. The OutFlow
W125 filters air before it is exhausted outdoors to help meet environmental
emission standards.
Isolation Areas
Infection control (e.g. tuberculosis) in hospitals and similar facilities
demands the creation of negative pressure environments to reduce the spread of
airborne microorganisms. The OutFlow W125 permits operation of the filter unit
from within the isolation area, eliminating the danger of housing leakage into
the surrounding area.
The OutFlow W125 kit easily modifies any IQAir filtration unit. Simply replace
the top module of any standard IQAir filtration unit with the TopFlow adapter.
All that is needed to install the ducting, wall tube and vent is a 5.2" opening
in a wall or window. The OutFlow W125 kit also includes a damper and a
protective mesh grille which prevents backdrafts and entry of coarse particles
when the system is not in use. The large 5" diameter of the ducting ensures low
air resistance.
The aluminum duct may be freely flexed to allow control over the desired vent
location. It is expandable in length from 10" in its original compressed state
to 39" when fully extended.
Creation of
Pressure Differentials
The OutFlow W125 lets you create pressure differentials between different indoor
areas. Negative pressure serves to contain pollutants in an isolation area.
Positive pressure protects a clean environment from uncontrolled infiltration of
airborne contaminants from polluted areas.
Emission Control
With the OutFlow W125 your IQAir® filtration device can be used for emission
control. Air is filtered and expelled outdoors via a flexible ducting system.
The negative pressure area that is created prevents unfiltered indoor air from
leaking outdoors.
IQAir Compatibility
Compatible with all IQAir® filtration devices and accessories.
To order or for more information
call 1-800-992-4739.
Best Selling Machines
